Tc Turrini

The water wall dust extractor has a double dust suction system. Outside there is a waterfall layer, generated to capture the heavier dust in suspension; inside there is another nozzle reduction system, needed for the complete dust removal of the suctioned air. Our suction cabin is designed for high performance and less maintenance. It is made of prime AISI 304 stainless steel. The MB water wall follows the guidelines of HSE Health and Safety Executive.

It is powered by:
- A power panel that is up to EC standards and American UL-CSA
- Submersible pump with pump body and back side impeller in AISI 304 stainless steel
- Highly energy efficient motors (category IE3)
- Easily removable drawer droplet separators on the front
- The containment tank below it is tilted for easy cleaning of the accumulated sludge

Models MB 20 MB 30 MB 40 MB 50 MB 60 MB 70
Length [mm] 2.080 3.080 4.080 5.080 6.080 7.080
Width [mm] 980 980 980 980 980 980
Height [mm] 2.300 2.300 2.300 2.300 2.300 2.300
N° of Vacuum Cleaners 1 1 2 2 3 3
Vacuum Cleaner’s Power [kW] 3 3 3 3 3 3
Pump’s Power [kW] 0.75 0.75 1.1 1.1 1.5 1.5
Power [kW] 3.75 3.75 7.1 7.1 10.5 10.5
Intake Air Amount [m³/h] 11.000 12.000 22.000 24.000 33.000 35.000
Noisiness [dB] 70 70 71 71 73 73
Dust Suppression 98.3% 98.3% 98.3% 98.3% 98.3% 98.3%
Tank Capacity [m³] 0.45 0.68 0.9 1.15 1.35 1.58
Unladen Weight [Kg] 340 420 560 670 860 970
Laden Weight [Kg] 850 1.200 1.500 1.900 2.250 2.700

The operation and use of the MODULBOX MB system requires the operator to work in the front of the module, between the water layer and the linear vacuum opening. The dust produced is vacuumed by the fans through the opening located between the tank and the water layer. At first, part of the dust is reduced by the outer water layer while the rest is stopped by a water atomization system located inside the machine. The module also has a droplet separator that isolates the water atomization system from the suction unit, not allowing the water or dust to be discharged in the air. The purified air comes out from the top of the machine, allowing recirculation in the location. The water flow on the outer layer can be regulated using the gate valves while the flow of the inner water atomization system, for dust reduction, remains constant. It is also possible to access the machine for cleaning and routine maintenance of parts subject to saturation and inevitable wear. An additional fixed or mobile box of various dimensions with a frame in AISI 304 stainless steel and plexiglass panels can be applied to the front allowing the user to work even in areas subject to excessive turbulence. Whenever the laboratory ceiling is not higher than six metres, our anti-turbulence disperser called the PLENUM is recommended.

1^ Fase

Primo abbattimento della polvere sospesa tramite velo d’acqua a cascata esterno.

2^ Fase

Secondo abbattimento della polvere residua tramite velo d’acqua interno.

3^ Fase

Filtrazione dell’acqua sospesa in aria tramite filtri ferma gocce in PVC.

4^ Fase

Fuoriuscita di aria purificata dal lato superiore della macchina.


TC Turrini TC Turrini


I consent to the processing of my personal data in compliance with the reg. 2016/679/EU and I declare that I have read the Privacy Policy
I agree to receive information about promotions, news and events related to this site in accordance with the new reg. 2016/679/EU on Privacy
T.C. Turrini Claudio srl
Via Francia, 4
37069 Villafranca (VR) Italy
Reg. Imp., C.F. e P.IVA IT 02897120230
R.E.A. N. 292864
Cap. Soc. € 93.383,68
Cod. Mecc. Est. VR042600 del 15/12/99
Tel. +39 045 6302744
Confindustria Marmomacchine Menbro